Motion blur in Premiere Pro
How to add motion blur to footage in Premiere Pro
Premiere’s motion blur tools are built for graphics you animate, not for movement already in the shot. Here is what each one does, and how to get blur that follows the real motion.
Updated November 4, 2026
If you search for motion blur in Adobe Premiere®, most answers point you to the Transform effect. That works for a title or a photo you animate yourself, but it does nothing to the movement inside a clip: a drone pass, an action camera, a timelapse, or the fast part of a speed ramp. Premiere has no built-in effect that measures the motion in footage and blurs along it. Editors have asked Adobe for native motion blur on speed ramps since January 2025, and the request is still open (Adobe Community). Below are the options inside Premiere and what each one is good for, then how Shutter does it.
Why some footage looks choppy
A camera blurs moving things in proportion to how long its shutter stays open. The classic film look uses a 180 degree shutter: an exposure of half the frame interval, about 1/48 of a second at 24 frames per second. Action cameras, drones and phones in bright light often shoot at 1/250 of a second or faster. Every frame is sharp, so fast motion stutters from one frame to the next instead of smearing. Speed ramps make it worse, because a sped-up section moves further between frames while each frame keeps its short exposure. The fix is blur that follows each pixel’s actual motion between frames.
What Premiere gives you
Transform effect: for motion you keyframe
Apply Transform from the Effects panel, uncheck Use Composition’s Shutter Angle, and set Shutter Angle: 180 is the usual start, higher gives more blur. Then animate Position, Scale or Rotation inside the Transform effect, not in the clip’s own Motion controls, because only Transform’s keyframes get blurred (Motion Array). Good for slides, zoom transitions and graphics. It does not touch the movement within the picture.
Directional Blur: one direction, the whole frame
Adobe’s own how-to adds the look of motion with Directional Blur: set a direction that matches the action, keep the blur length modest, and mask the moving subject if the background should stay sharp (Adobe, Adobe effect reference). It blurs everything under the mask the same way, so it suits a whip pan or the peak of a speed ramp, keyframed on and off, better than a shot with several things moving in different directions.
Frame Blending and Optical Flow: for frame rates, not blur
Time interpolation on a slowed or sped-up clip (Frame Blending or Optical Flow) builds in-between frames. That smooths a speed change, but it is not motion blur: frame blending gives soft double images, and optical flow can warp edges on complex motion.
After Effects: Pixel Motion Blur
After Effects has a Pixel Motion Blur effect that analyzes the footage and builds blur from motion vectors, with its own shutter angle (Adobe). It is the real thing, at the cost of a round trip: replace the clip with an After Effects composition, apply the effect there, and wait for it to render back in Premiere.
Shutter: motion blur that follows the footage, inside Premiere
Shutter is an effect for Premiere. It tracks the motion of every pixel in the shot and blurs along it, so a fast background smears, a passing car streaks, and the parts of the frame that are not moving stay sharp. There are no keyframes to set.
- In the Effects panel, search for Shutter and drag it onto a clip.
- Set Blur Amount, in shutter degrees. 180 is the classic film look, and makes 1/250 second footage read like 1/48. Go higher for a heavier, dreamier blur.
- Pick a Mode. AI Motion is the everyday mode and tracks the real motion. Zoom is for push-ins and fast zooms, Linear blurs the whole frame in one direction it works out for itself, and Spin is for wheels, propellers and fans, where you set the center and the rate. The panel shows only the controls the chosen mode uses.
- On a tracking shot, raise Keep Subject Sharp so the moving background does not smear over your subject, and use Feather to soften the edge between the two.
- If the blur looks splotchy on a plain surface such as sky, a wall or water, raise Flow Smoothing.
On a speed ramp
Nest the ramped clip (right-click, Nest) and apply Shutter to the nested sequence. The blur then follows the speed: the fast sections get long streaks and the slow-motion sections short ones, the way a camera would have recorded them.
On animated titles and graphics
Premiere applies effects before a clip’s own Motion settings, so a title animated with Position or Scale looks still to any effect on that clip. Nest the graphic first and apply Shutter to the nest, and it gets clean streaks without the Transform effect.
Playback
Shutter works out the motion for every pixel of every frame, so it slows timeline playback. Set the look on a short preview range, then render in to out for smooth playback.
When you do not need Shutter
- Graphics you animate yourself. The Transform effect’s shutter angle is free and does the job.
- Footage shot at a 180 degree shutter. It already has natural blur. Adding more is a look, not a fix.
- Your machine is not supported. Shutter runs on macOS 14 or later, Apple silicon; or Windows 10 or 11, 64-bit, NVIDIA GPU with CUDA (GTX 10-series or newer). It needs Adobe Premiere 2025 or later, with GPU acceleration on (Software Only is not supported). AMD and Intel graphics on Windows are not supported yet.
Try it on your own footage
Try every tool free for 7 days, with 100 AI credits (about 10 generations). You can also buy Shutter outright. The Shutter page has a before-and-after slider on real footage, and pricing has both options.
Cutting interviews or podcasts too? See how to rough cut interviews faster in Premiere.
